thoughtsasa.blogg.se - Snap on modis ultra key programming

Snap on modis ultra key programming update#
Snap on modis ultra key programming code#

Check to ensure vehicle does not have an aftermarket engine immobilizer.

Disable any Remote Starter equipment, especially anything nearby the PATS Ford FCSD Dealer installed Remote Starter systems are approved for use in Ford vehicles.

Snap on modis ultra key programming update#

If i update to 9. As far as i know only they dealer with a tech 2 can do it.

Check to ensure vehicle does not have an aftermarket remote starter. Got the Modis v6.4, Need to program new key remote control to a 2000 Cadi Deville.

Check to make sure the issue is not with multiple PATS keys, small electronic devices that can be used to purchase gasoline, or other items on same key ring.

Be certain of the vehicle model Use only parts & keys speciﬁed for the appropriate model year.

Look for fault codes in The PATS function will store fault codes when the PCM records a P1260.

Disconnect battery cables when replacing PATS module, ICM, VIC, HEC, SCIL, PCM, or.

When replacing ignition keys, make sure the owner throws out ALL old.

Disconnect the diagnostic tool for 20 seconds before cycling ignition to OFF, ACC, or RUN.

Review Service Procedures and Technical Service Bulletins (TSBs) for latest.

Select “ICM / PCM Parameter Reset.” Select “PCM / TCM Parameter Reset” and then Exit Security Access. Perform a PCM Keep Alive Memory (KAM) reset.Įnter Security Access on the PATS control function module. Select “Parameter Reset” and then Exit Security Access. Enter Security Access on the PATS control function module. Cycle new key to RUN.Ĭycle a key in ignition to RUN. Spare Ke y Programming Using Programmed Keysġ key required.

Snap on modis ultra key programming code#

Select “Ignition Key Code Program.” Disconnect Tool and leave key in RUN for 20 seconds. Spare Ke y Programming Using Di a gnosti c T oolsĬycle an unprogrammed key in ignition to RUN. Cycle key 1 to OFF, then RUN, and back to OFF. Select “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Cycle key to OFF and then RUN.Ģ keys required. Enter “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Retrieve DTCs from applicable PATS control function (PATS/ICM/VIC/HEC/SCIL).ġ key required. PCM disabled the vehicle because of a PATS concern. Key program failure (defective key or transceiver).Ĭommunications issue, SCP (J1850), between PCM and PATS control (PATS/ICM/ VIC/HEC/SCIL).Ĭommunications issue, CAN (J2284), between PCM and PATS control (ICM). PCM ID does not match between the PCM and PATS control (PATS/ICM/VIC/HEC/SCIL). Non-Volatile Memory (NVM) conﬁguration failure - No PCM ID stored in PATS. Partial detection of encoded ignition key. Unprogrammed encoded ignition key detected (leave ignition on for 20 seconds before trying a programmed key, in Anti-Scan Mode). Replace transceiver.ĮCU is defective (EEPROM in PCM is not working - replace PCM). (ABS/Engine/Airbag)ĭetails and specificity vary by manufacture.įor example, Autel MS906BT program key on a Honda Accord.Less than 2 (or 3 if equipped w/Valet key) keys programmed to the system.

Refine the results by typing key in the Function boxĬoverage will be listed in an undetermined order, grouped by System. Searching the tested models on the official site:Īutel Maxisys coverage are available here:ġ.Choose the Autel Tool from the list (i.e. The Autel does not pull PINs, in some cases you can bypass the PIN requirement. If OE requires PIN and if you have the pin, then Autel might do it. If OE requires programming then a J2534 device must be used and an LSID may be needed. If OE does it by activating or coding, then Autel probably will do it. Generally speaking, it depends on manufacturer. I was able to get the pin code for a vehicle I own but if it is a customer’s vehicle they may not give you the code, only perform the work and charge you.

Pin codes however must be obtained from a dealer or locksmith as they are highly protected by manufacturers for obvious reasons. Autel MaxiSys MS906BT can program keys and RKE fobs on certain vehicles. Question: Is it possible to use Autel MaxiSys MS906BT for key programming and pin code reading?